| Concrete vibrators | Ceiling Grinders | Flexible Shafts | Rebar Shakers |

Oztec RubberHeadTM Concrete Vibrator

Oztec Concrete Vibrator Header





Rebar ShakerTM


Rebar ShakerTM

Heavy Duty


Steel Heads


Pencil Heads


Heads for Tilt-Up


Rubber Tips




Electric Power Units


Gas Power Units


Back Packs




Flexible shafts


Adapter Couplings






Selection Chart


Tips & Suggestions




Ceiling Grinders


Oztec Patented RubberHead


Oztec Concrete Vibrator RubberHead

Rebar protected by Oztec's

Patented action RubberheadTM


Epoxy Coated Rebar

Eliminates damage to epoxy coated rebar caused by a standard steel vibrator head


See Best Solution for

Tilt-Up Construction

Click Here


Choice of shapes and sizes
for any application

All dimensions shown are nominal, actual dimensions may vary.

Call for details.

(Click here for Head, Shaft and Power Unit selection chart)


  RubberHeadTM  (also see Steel Head page  and  Short Head Tilt-Up page)

Oztec's "High Efficiency RubberHeadTM" Outperforms any other type of vibrator

Epoxy coated rebar presents a particularly troublesome problem. Steel heads act like an electric hammer, striking any rebar or forms they contact, over 10,000 times per minute, with a force from hundreds to over 2,000 pounds per blow. Contact with a steel vibrator head of as little as one second can chip enough coating to subject the steel to deep rust. Oztec's patented High Efficiency "RubberHeadTM" vibrator head not only meets DOT non-metal head specifications for protecting coated rebar and expensive forms, but exhibit some very special and unique properties. The High Efficiency "RubberHeadTM" urethane dimpled construction sends strong shock waves off the entire length of the head, with a larger radius of action, producing denser concrete with less voids to patch.

Oztec's patented "High Efficiency RubberHeadTM":

  • Will outperform any other type of vibrator?round, square, hi-cycle, etc?Any Type!

  • Will protect epoxy coated rebar and expensive forms.
  • Is outstanding in low slump (to "0" slump) concrete.
  • Essential in large pours of very stiff concrete. 
  • Makes concrete denser with less voids to patch.
  • Vibrates @ 12,000vpm, never drops below 10,500vpm when lowered deep into low slump concrete.
  • Provides Superior Action.
  • Is an absolute must for Architectural concrete where cosmetic surfaces are essential.
  • All Oztec vibrators meet or exceed ACI specification # 309

Why the Oztec "RubberHeadTM" outperforms any other type of Vibrator.
(a.) When a smooth vibrator head (round, square or any other shape) is lowered into a relatively stiff concrete batch, the front or nose of the vibrator drills a hole. It pushes away concrete faster than it can return. Result, shock waves produced mostly from the vibrator's front end.

(b.) Oztec's patented "RubberHeadTM" has a large number of openings which allow wet concrete to cool the inner shell. These openings act like "suction cups", which keeps concrete in contact with the entire length of the vibrator head, sending strong shock waves into the mass.

Prevent Hang-ups in

Congested Rebar
With Oztec extension pieces, you can greatly reduce the chance of vibrator heads getting caught in the rebar. Oztec RubberHeads? or Steel heads have the option of being equipped with extension pieces.

In 1913,replica bags founded the first boutique in the heart of Milan,Italy,and the founder replica watches uk designed Mario Prada's fashionable and high quality replica watches ,suitcases,gucci fake and replica bags.One of the hermes replica ,the other is gucci replica .

              Oztec's patented uniform, high efficiency action.

    (a.) Smooth vibrator head (b.) Oztec's patented "RubberHeadTM"  
Prove it to yourself!
Before you purchase a high cycle system with expensive generators or controllers,    call:  800-533-9055 or visit our web site to arrange a demonstration on your job site.

Home | Oztec Products | The Company | Contact Us | What's New | PDF Catalog | Trade Shows |

Oztec Industries, Inc. ? 2010  |  Privacy